V
vano
Гость
Всем привет, тв висит на заставке, неоднократно входил на этих шаськах в терминал, а тут засада, никак не реагирует не на какие зажатия и нажимания клавиш. Это Ctrl+C, enter, esc, пробел, никак не входит.
Лог при включении есть, а при загрузке выдает постоянно. Пробовал уже все проги которые есть, в том числе и PuTTY. Может еще есть какие способы как попасть в консоль?
Начальный лог прилагаю.
Лог при включении есть, а при загрузке выдает постоянно. Пробовал уже все проги которые есть, в том числе и PuTTY. Может еще есть какие способы как попасть в консоль?
Начальный лог прилагаю.
Boot-
EFUSE=3;
DRAM Channel A Calibration.
1T = (108 - 34) = 74 delay cells
Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell =15 ps
Byte 0 : Gating(-26 ~ 27), Size=54 .
Byte 1 : Gating(-27 ~ 28), Size=56 .
Byte 2 : Gating(-24 ~ 25), Size=50 .
Byte 3 : Gating(-25 ~ 26), Size=52 .
HW Byte 0 : DQS(-14 ~ 13), Size 28 , Set 0.
HW Byte 1 : DQS(-13 ~ 12), Size 26 , Set 0.
HW Byte 2 : DQS(-11 ~ 11), Size 23 , Set 0.
HW Byte 3 : DQS(-13 ~ 12), Size 26 , Set 0.
DATLAT calibration
first_step= 17 total pass= 6 best_step=19 .
TX HW Byte 0 : DQS(26 ~ 50), Size 25, Set 38.
TX HW Byte 1 : DQS(26 ~ 51), Size 26, Set 38.
TX HW Byte 2 : DQS(28 ~ 50), Size 23, Set 39.
TX HW Byte 3 : DQS(31 ~ 53), Size 23, Set 42.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
EMMC boot
.
CID:0x4fc876f7
:0x52061398
:0x47544634
:0x15010038
LZHS addr:0x00100040
LZHS size:0x000f25c0
LZHS size:0x0005f929
LZHS checksum:0x000000a1
LZHS begin
LZHS ok
Boot
Start Lmain
MT5863 Boot Loader v0.9
MUSB_Init : ++
It has 2 USB Port,is 1, 1, 0, 0(1=using, 0=not use).
USB0: Set GPIO-1 = 1.
USB0: Set GPIO-1 error.
USB1: Set GPIO-1 = 1.
USB1: Set GPIO-1 error.
USB Port 0 is initial.
USB Port 1 is initial.
Set port-0 to Host mode.
Set port-1 to Host mode.
Support network![MSDC] LOADER FAST READ EMMC!
[MSDC] Init config, cid = 0x15010038, dsc=0x4fc876f7, rca=0x52061398, ocr=0x47544634
[MSDC] loader RCA 1, 1
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] MT22627:15010038:47544634:52061398:4fc876f7
[MSDC] id1:00384754 id2:46345206
[MSDC] eMMC Name: UNKNOWN
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] Prepare set msdc Bus Clock as HS25(MHz),src 12 ,mode 0, div 4
[MSDC] Set Bus Clock as HS25(MHz) Success!,src 12 ,mode 0, div 4
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] [eMMC2DRAM]enter into SDR50 Mode, max dtr 200000000
[MSDC] Prepare set msdc Bus Clock as HS0(MHz),src 0 ,mode 0, div 16
[MSDC] Set Bus Clock as HS0(MHz) Success!,src 0 ,mode 0, div 16
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 0 !
[MSDC] Prepare set msdc Bus Clock as HS50(MHz),src 12 ,mode 0, div 2
[MSDC] Set Bus Clock as HS50(MHz) Success!,src 12 ,mode 0, div 2
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC]
Saved info: id1 = 0x76f75206, id2=0x13984754,flag 0xaabbccdd,speedmode 5, dlycell 75
[MSDC] Support HS400, card type ext_csd[196]0x57
[MSDC] Support HS200, card type ext_csd[196]0x57
[MSDC] u4mask = 0x3
[MSDC] ID: 0x15010038, 0x47544634, 0x52061398, 0x4fc876f7
[MSDC]
Cur info: id1 = 0x76f75206, id2=0x13984754,flag 0xaabbccdd,speedmode 5, dlycell 74
[MSDC]
-----The information is match, Alrady run autok before, ignore this time--
[MSDC] Load Param:
[MSDC] K_IOCON: 0x200000a
[MSDC] K_PAD_TUNE0: 0x222000
[MSDC] K_PAD_TUNE1: 0x0
[MSDC] K_PATCH_BIT0: 0x403c0006
[MSDC] K_PATCH_BIConnect interrupt = 0x10, pBase = 0xf0050000.
T1: 0xfffe4309
[MSDC] K_PATCH_BIT2: 0x448a1803
[MSDC] K_EMMC50_CFG0: 0xe88832
[MSDC] K_DAT_RD_DLY0: 0x4040504
[MSDC] K_DAT_RD_DLY1: 0x3020404
[MSDC] K_DAT_RD_DLY2: 0x0
[MSDC] K_DAT_RD_DLY3: 0x0
[MSDC] K_EMMC50_PAD_DS_TUNE: 0x11025
[MSDC] K_EMMC50_PAD_CMD_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT01_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT23_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT45_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT67_TUNE: 0x0
[MSDC] Current speed mode 1, clock 50.
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] --ENTER RPMB--
[MSDC] --EXIT RPMB--
[MSDC] Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell = 15 ps
[MSDC] TCMGET_DLYCELL_PERT = 74
1st MAC in EEP is valid (70:2e:d9:ff:c7:e3)
Boot reason: A/C power on!!11111 u1AtmosEnable = 10
Remove Quiet Boot misc control in eeprom when Watchdog reason.
Normal zcc Start,using customer ir
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x dbbc98, size: 21076)success!!
T8032 FW version: 6
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x69d00 0x80
<5507> getenv flag=0x1a01, len=0x0b
[readRecoveryCmd] readRecoveryCmd start
recovery cmd:,para:
Do USB upgrade
u1USBBlock = 0x01d0a480
USB: Vbus turn up time = 318 ms, Max =1000 ms.
USB-0: insert.
Device High speed.
MGC_HostEnumerator:MGC_EnumStateGetMaxDevice
HubPort-0: Device reset.
Silent Reset: Root device = 0x01d0b6c4, Reset.
MGC_HostEnumerator:MGC_EnumStateReset
HubPort-0: Device address = 1.
MGC_HostEnumerator:MGC_EnumStateSetAddress
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: idVendor = 0x3538.
HubPort-0: idProduct = 0x0054.
HubPort-0: bcdDevice = 0x0100.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Lang Id: 0x409.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Manufacturer: P Technology.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Product: USB Mass Storage Device.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: SerialNum: 000000000000E7.
MGC_HostEnumerator:MGC_EnumStateSizeConfigs
MGC_HostEnumerator:MGC_EnumStateGetConfigs
MGC_HostEnumerator:MGC_EnumStateConnectDevice
USB Enumerator: find device driver
MGC_HostFindDriver:++
MUSB_TARGET_CLASS case 2:bMatch =1, 0x0,0x0
MUSB_TARGET_CLASS case1:bMatch =1,0x8,0x8
MUSB_TARGET_ACCEPT:bMatch = 1
HubPort-0: Driver support, class = 0x8.
USB Enumerator: Driver support
HubPort-0: Device is accepted.
HubPort-0: Device is accepted.
MGC_HostEnumerator:Connect device complete, bRet=1
MGC_HostEnumerator: break connect device
LUN = 0-1.
vid = 0x3538, pid = 0x0054, bMediumStatus = 0.
USB-0: ClassCode= 0x8, u4Diff=0 ms.
MUSB_GetInsert return 1
prLdrData->rDtvCfg.u1Upgrade_Ext :0x0
_fgDeviceType :0x0
FIND_CLASS_MASS_STORAGE.
Wait USB medium to be mounted...
LUN = 0-1.
ID = Generic USB Flash Disk 0.00. [RW].
Block size = 512 bytes, Total size = 1927 Mbytes.
MUSB_HfiMediumInserted().
USB Medium on Device, Time = 536 ms.
USB block size = 512 bytes.
/dev is created.
/mnt is already existed. That is OK.
/dev/usb is created.
/mnt/usb_0 is created.
/dev/usb_0 is mounted as /mnt/usb_0.
Error: No allupgrade_5510_8G_1G_ref70xxx.pkg was found
Error: No valid upgrade file found, USB upgrade stop
LDR_EEPUserDrvCheckMagic u4HeaderData=0x14100602, u4Magic=0x14100602
<5508> getenv flag=0x1a09, val=0x00
<5508> LDR_IsGoBootup prLdrData->u4WakeupReason:6
<5508> getenv flag=0x1a08, val=0xff
<5508> setenv flag=0x1421, val=0xff
<5508> LDR_IsGoBootup AT_READ_FLAG=0, AT_B_FLAG=255
go to standby when ac on at factory mode 0.
RT710.dbg Loader_RT710_Standby
rt710.dbg ucI2cWrite_tuner OK
rt710.dbg ucI2cWrite_tuner OK
joe.dbg LDR I2C OK
Servoadc Channel1 frist update!!!, value is 1023
Servoadc Channel1 finish update!!!, value is 1023
Normal zcc Start,using customer ir
Disable VGA wakeup
powerdown usb port2
support WOL
wol off, MAC register switch to arm
star:mtcmos poweroff eth
11111 u1AtmosEnable = 10
loader The output gpio is 209 pfgSet0
loader The output gpio is 209 pfgSetis null
Standby
PDWNC_EnterPowerDown(200100,6)
SWITCH_T8032
EFUSE=3;
DRAM Channel A Calibration.
1T = (108 - 34) = 74 delay cells
Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell =15 ps
Byte 0 : Gating(-26 ~ 27), Size=54 .
Byte 1 : Gating(-27 ~ 28), Size=56 .
Byte 2 : Gating(-24 ~ 25), Size=50 .
Byte 3 : Gating(-25 ~ 26), Size=52 .
HW Byte 0 : DQS(-14 ~ 13), Size 28 , Set 0.
HW Byte 1 : DQS(-13 ~ 12), Size 26 , Set 0.
HW Byte 2 : DQS(-11 ~ 11), Size 23 , Set 0.
HW Byte 3 : DQS(-13 ~ 12), Size 26 , Set 0.
DATLAT calibration
first_step= 17 total pass= 6 best_step=19 .
TX HW Byte 0 : DQS(26 ~ 50), Size 25, Set 38.
TX HW Byte 1 : DQS(26 ~ 51), Size 26, Set 38.
TX HW Byte 2 : DQS(28 ~ 50), Size 23, Set 39.
TX HW Byte 3 : DQS(31 ~ 53), Size 23, Set 42.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
EMMC boot
.
CID:0x4fc876f7
:0x52061398
:0x47544634
:0x15010038
LZHS addr:0x00100040
LZHS size:0x000f25c0
LZHS size:0x0005f929
LZHS checksum:0x000000a1
LZHS begin
LZHS ok
Boot
Start Lmain
MT5863 Boot Loader v0.9
MUSB_Init : ++
It has 2 USB Port,is 1, 1, 0, 0(1=using, 0=not use).
USB0: Set GPIO-1 = 1.
USB0: Set GPIO-1 error.
USB1: Set GPIO-1 = 1.
USB1: Set GPIO-1 error.
USB Port 0 is initial.
USB Port 1 is initial.
Set port-0 to Host mode.
Set port-1 to Host mode.
Support network![MSDC] LOADER FAST READ EMMC!
[MSDC] Init config, cid = 0x15010038, dsc=0x4fc876f7, rca=0x52061398, ocr=0x47544634
[MSDC] loader RCA 1, 1
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] MT22627:15010038:47544634:52061398:4fc876f7
[MSDC] id1:00384754 id2:46345206
[MSDC] eMMC Name: UNKNOWN
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] Prepare set msdc Bus Clock as HS25(MHz),src 12 ,mode 0, div 4
[MSDC] Set Bus Clock as HS25(MHz) Success!,src 12 ,mode 0, div 4
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] [eMMC2DRAM]enter into SDR50 Mode, max dtr 200000000
[MSDC] Prepare set msdc Bus Clock as HS0(MHz),src 0 ,mode 0, div 16
[MSDC] Set Bus Clock as HS0(MHz) Success!,src 0 ,mode 0, div 16
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 0 !
[MSDC] Prepare set msdc Bus Clock as HS50(MHz),src 12 ,mode 0, div 2
[MSDC] Set Bus Clock as HS50(MHz) Success!,src 12 ,mode 0, div 2
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC]
Saved info: id1 = 0x76f75206, id2=0x13984754,flag 0xaabbccdd,speedmode 5, dlycell 75
[MSDC] Support HS400, card type ext_csd[196]0x57
[MSDC] Support HS200, card type ext_csd[196]0x57
[MSDC] u4mask = 0x3
[MSDC] ID: 0x15010038, 0x47544634, 0x52061398, 0x4fc876f7
[MSDC]
Cur info: id1 = 0x76f75206, id2=0x13984754,flag 0xaabbccdd,speedmode 5, dlycell 74
[MSDC]
-----The information is match, Alrady run autok before, ignore this time--
[MSDC] Load Param:
[MSDC] K_IOCON: 0x200000a
[MSDC] K_PAD_TUNE0: 0x222000
[MSDC] K_PAD_TUNE1: 0x0
[MSDC] K_PATCH_BIT0: 0x403c0006
[MSDC] K_PATCH_BIConnect interrupt = 0x10, pBase = 0xf0050000.
T1: 0xfffe4309
[MSDC] K_PATCH_BIT2: 0x448a1803
[MSDC] K_EMMC50_CFG0: 0xe88832
[MSDC] K_DAT_RD_DLY0: 0x4040504
[MSDC] K_DAT_RD_DLY1: 0x3020404
[MSDC] K_DAT_RD_DLY2: 0x0
[MSDC] K_DAT_RD_DLY3: 0x0
[MSDC] K_EMMC50_PAD_DS_TUNE: 0x11025
[MSDC] K_EMMC50_PAD_CMD_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT01_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT23_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT45_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT67_TUNE: 0x0
[MSDC] Current speed mode 1, clock 50.
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] --ENTER RPMB--
[MSDC] --EXIT RPMB--
[MSDC] Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell = 15 ps
[MSDC] TCMGET_DLYCELL_PERT = 74
1st MAC in EEP is valid (70:2e:d9:ff:c7:e3)
Boot reason: A/C power on!!11111 u1AtmosEnable = 10
Remove Quiet Boot misc control in eeprom when Watchdog reason.
Normal zcc Start,using customer ir
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x dbbc98, size: 21076)success!!
T8032 FW version: 6
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x69d00 0x80
<5507> getenv flag=0x1a01, len=0x0b
[readRecoveryCmd] readRecoveryCmd start
recovery cmd:,para:
Do USB upgrade
u1USBBlock = 0x01d0a480
USB: Vbus turn up time = 318 ms, Max =1000 ms.
USB-0: insert.
Device High speed.
MGC_HostEnumerator:MGC_EnumStateGetMaxDevice
HubPort-0: Device reset.
Silent Reset: Root device = 0x01d0b6c4, Reset.
MGC_HostEnumerator:MGC_EnumStateReset
HubPort-0: Device address = 1.
MGC_HostEnumerator:MGC_EnumStateSetAddress
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: idVendor = 0x3538.
HubPort-0: idProduct = 0x0054.
HubPort-0: bcdDevice = 0x0100.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Lang Id: 0x409.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Manufacturer: P Technology.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Product: USB Mass Storage Device.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: SerialNum: 000000000000E7.
MGC_HostEnumerator:MGC_EnumStateSizeConfigs
MGC_HostEnumerator:MGC_EnumStateGetConfigs
MGC_HostEnumerator:MGC_EnumStateConnectDevice
USB Enumerator: find device driver
MGC_HostFindDriver:++
MUSB_TARGET_CLASS case 2:bMatch =1, 0x0,0x0
MUSB_TARGET_CLASS case1:bMatch =1,0x8,0x8
MUSB_TARGET_ACCEPT:bMatch = 1
HubPort-0: Driver support, class = 0x8.
USB Enumerator: Driver support
HubPort-0: Device is accepted.
HubPort-0: Device is accepted.
MGC_HostEnumerator:Connect device complete, bRet=1
MGC_HostEnumerator: break connect device
LUN = 0-1.
vid = 0x3538, pid = 0x0054, bMediumStatus = 0.
USB-0: ClassCode= 0x8, u4Diff=0 ms.
MUSB_GetInsert return 1
prLdrData->rDtvCfg.u1Upgrade_Ext :0x0
_fgDeviceType :0x0
FIND_CLASS_MASS_STORAGE.
Wait USB medium to be mounted...
LUN = 0-1.
ID = Generic USB Flash Disk 0.00. [RW].
Block size = 512 bytes, Total size = 1927 Mbytes.
MUSB_HfiMediumInserted().
USB Medium on Device, Time = 536 ms.
USB block size = 512 bytes.
/dev is created.
/mnt is already existed. That is OK.
/dev/usb is created.
/mnt/usb_0 is created.
/dev/usb_0 is mounted as /mnt/usb_0.
Error: No allupgrade_5510_8G_1G_ref70xxx.pkg was found
Error: No valid upgrade file found, USB upgrade stop
LDR_EEPUserDrvCheckMagic u4HeaderData=0x14100602, u4Magic=0x14100602
<5508> getenv flag=0x1a09, val=0x00
<5508> LDR_IsGoBootup prLdrData->u4WakeupReason:6
<5508> getenv flag=0x1a08, val=0xff
<5508> setenv flag=0x1421, val=0xff
<5508> LDR_IsGoBootup AT_READ_FLAG=0, AT_B_FLAG=255
go to standby when ac on at factory mode 0.
RT710.dbg Loader_RT710_Standby
rt710.dbg ucI2cWrite_tuner OK
rt710.dbg ucI2cWrite_tuner OK
joe.dbg LDR I2C OK
Servoadc Channel1 frist update!!!, value is 1023
Servoadc Channel1 finish update!!!, value is 1023
Normal zcc Start,using customer ir
Disable VGA wakeup
powerdown usb port2
support WOL
wol off, MAC register switch to arm
star:mtcmos poweroff eth
11111 u1AtmosEnable = 10
loader The output gpio is 209 pfgSet0
loader The output gpio is 209 pfgSetis null
Standby
PDWNC_EnterPowerDown(200100,6)
SWITCH_T8032
Последнее редактирование модератором:
