ivannovichok
Участник
main: 715G5713-M01-000-005k
Принесли аппарат с проблемой нет изо после логотипа. Имеются все напряжение с БП подсветка включается, но после логотипа серый экран, выключить возможно только с розетки. Прошивал 24_128 и nand с похожих плат, но дефект тоже самый(менял микрухи). По uart выдаёт ошибку тюнера как я понимаю, включал без него и менял на заведомо рабочий та же ошибка. Что может быть?
Boot-
DRAM Channel A Calibration.
Byte 0 : Gating(2 ~ 77), Size=76, Mid=41, Set=41.
Byte 1 : Gating(2 ~ 62), Size=61, Mid=34, Set=34.
Byte 2 : Gating(2 ~ 87), Size=86, Mid=46, Set=46.
Byte 3 : Gating(2 ~ 82), Size=81, Mid=44, Set=44.
Byte 0 : DQS(5 ~ 43), Size 39, Set 23.
Byte 1 : DQS(8 ~ 40), Size 33, Set 22.
Byte 2 : DQS(6 ~ 41), Size 36, Set 21.
Byte 3 : DQS(11 ~ 38), Size 28, Set 20.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
0x0000a000
Nand boot
NID=0x9510dcec
LZHS addr:0x00100040
LZHS size:0x001f8fd0
LZHS checksum:0x00000042
Boot
Start Lmain
MT5880 Boot Loader v1.11
SIF_Master0: new design
Boot reason: A/C power on!!
[PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0)
-------------use external edid, disable internal edid------------------
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x d450f8, size: 24286)success!!
T8032 FW version: 18
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x73500 0x80
Detect NAND flash ID: 0x9510DCEC
Detect SS K9F4G08U0B/D NAND flash(SLC): 512MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000
NAND_BDM_Mount: Partid: 0, Total Block Count: 16, Bad Block Count: 0
1st MAC in EEP is valid (1c:5a:6b:41:25:e1)
1st : (1c:5a:6b:41:25:e1)
2nd : (1c:5a:6b:41:25:e1)
[PDWNC] Current state : 0x1
[PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6
PDWNC_PHILIPS_DetermineNextState : u4Current = 1
PDWNC_PHILIPS_DetermineNextState : system booting
PDWNC_PHILIPS_DetermineNextState : event = PDWNC_WAKE_UP_REASON_AC_POWER
Read EEPROM OK at PDWNC_PHILIPS_GetLoungeMode
PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0
Current = 0x1, Event = 0x6, Next = 0x1
[PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1
[PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_Init
USB0: Set GPIO63 = 1.
USB1: Set GPIO64 = 1.
Display 0x00efe5b8 background:0x00000000
Find panel index 215 from EEPROM
OSD_SetPlaneSwitchOrder[0,1,2],Switch[1,2,3]
---------- [SA7] vErrorHandleInit ----------
[SA7] Error handling init
[SA7] PANEL_GetPanelWidth=0x556, PANEL_GetPanelHeight=0x300 , wDrvGetOutputHTotal=0x898 , wDrvGetOutputVTotal=0x465
[SA7] PANEL_GetHTotalMax=0x6e6, PANEL_GetHTotalMin=0x5b0, PANEL_GetVTotalMax=0x3f0, PANEL_GetVTotalMin=0x314
[SA7] PANEL_GetPixelClkMax=80000000, PANEL_GetPixelClkMin=63000000
[SA7] PANEL_GetPixelClk60Hz = 0x45126c0
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=260, u2HSyncStart=1930, u2VSyncWidth=26, u2VSyncStart=1094
---------- [SA7] vErrorHandleSetByTiming end----------
---------- [SA7] vErrorHandleSetByPanel end----------
[SA7] vDDDSInit
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=30, u2HSyncStart=1382, u2VSyncWidth=3, u2VSyncStart=784
---------- [SA7] vErrorHandleSetByTiming end----------
vDrvSetOCLKClockSchemaInit.
[SA7] _fgVopllUseDDDS = True
[LVDS] VOPLL Initialize successful !
LDR_OsdDisplay(14, 0x00d65bc0, 1280, 291)
Color:14 BmpAddr:0x00d65bc0 Width:1280 Height:291
Panel 1366 x 768
*************u4BmpPitch=5120******************
Do USB upgrade
USB: Vbus turn up time = 1419 ms, Max =0 ms.
USB-0: insert.
USB-0: ClassCode= 0x9, u4Diff=120 ms.
FIND_CLASS_HUB.
HUB No USB Medium on Hub.
USB upgrade stop
Flash load lzhs header from 0x80000 to dram(0x1526170), size=2048
Decompression uboot to 0x00800000...
Flash load image from 0x80000 to dram(0x1526170), size=0x400ab
NAND_BDM_Mount: Partid=4, offset=0x300000, size=0x400000
NAND_BDM_Mount: Partid: 4, Total Block Count: 32, Bad Block Count: 0
Flash load tz from 0x21acfb(kernel) to dram(0x3f200000), size=0x2b1b6
secure boot ok
secure boot ok
Starting image...
▒
U-Boot 2011.12.12 (Sep 27 2013 - 10:33:26)
DRAM: 725.3 MiB
WARNING: Caches not enabled
NAND: Detect NAND flash ID: 0x9510DCEC
Detect SS K9F4G08U0B/D NAND flash: 512MB
512 MiB
0.0.0.0
In: serial
Out: serial
Err: serial
Boot from kernelA and rootfsA(partition 6)
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
Partition rootfsA defined at mtdparts:
ID:6, Offset:0x00000000, Size:0x00b00000
Loader succeeded in signature verification
## Booting kernel from Legacy Image at 00007fc0 ...
XIP Kernel Image ... OK
OK
Starting kernel ...
TZ Heap: start=0x3FA5C5C0, end=0x40000000
TZ dram: start=0x3F000000, end=0x40000000
[ 0.000000] timekeeping_init done
INIT: version 2.86 booting
Loading /etc/profile...
Start readahead /etc/readahead_early
Running rc.local...
net.ipv4.tcp_window_scaling = 6
INIT: Entering runlevel: 3
**********DirectFBInit()
commandline read: app_man
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
(c) 2001-2009 The world wide DirectFB Open Source Community
(c) 2000-2004 Convergence (integrated media) GmbH
----------------------------------------------------------------
======DFB 3DMM u4VirtAddr : 0x3a6c5000, and DFB 3DMM u4Size : 0x1f80000======
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
input thread's parent pid is 517 tid is 517
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[DirectFB]: Wait to Init IR...!
[input_add_device][1629]
dfb_set_cursor_border [0,0,1280,0]
[dtv_app_mtk]>drv_init as 0x39 model
[dtv_app_mtk]>drv_init as EU model
[dtv_app_mtk]>HDMI fast booting init...
[ 8.507639] NAND_SDM_Mount: Partid=15, offset=0x1d680000, size=0x2980000
input thread pid is 517 tid is 525
original scheduler policy 0
scheduler nice 0
original child scheduler policy 0 prio 0
new child scheduler policy 2 prio 99
Start to wait IR event...
[dtv_app_mtk]>
[dtv_app_mtk]>TVD MsgCtrl: NRL:60/40, PER:100/90
[dtv_app_mtk]>x_drv_init end!!
[dtv_app_mtk]>[ FakeDM ] Init...
[FakeDM] Init FM...
/dev is created./mnt is already existed. That is OK.
/mnt/usb is created.[FakeDM] FM inited...
[FakeDM] Init SMB...
[FakeDM] SMB inited...
[FakeDM] do coldboot start...
[DM] _dm_open_dev_thread: entered
[DM] _dm_nfy_req_thread enter
[DM] _dm_nfy_req_thread get_nl_sock:26
[DM] _dm_cb_msg_thread enter
[DM] usbfs mounted.
[FakeDM] do coldboot end!!!
Init chip_spec_init!!!!!
EEPROM size is 0x4000.
{CI_glue}:ci_eng_init
{CI_glue}- expect PROD key
{CI_glue}- c[1]
88888888888888 PHYSICAL_Init() entered 888888888888888
88888888888888 ITC_Init() entered 888888888888888
88888888888888 PHYS_DRVOpen() entered 888888888888888
88888888888888 STB_CIOpen() entered 888888888888888
88888888888888 STB_CIOpen() ended 888888888888888
{CI}CI_RegInterrupt_nfy
88888888888888 PHYS_DRVOpen() entered 888888888888888
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 255
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank Line 9708
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[dtv_app_mtk]>
[dtv_app_mtk]> ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
[dtv_app_mtk]> (c) 2001-2009 The world wide DirectFB Open Source Community
[dtv_app_mtk]> (c) 2000-2004 Convergence (integrated media) GmbH
[dtv_app_mtk]> ----------------------------------------------------------------
[dtv_app_mtk]>
[dtv_app_mtk]>[dfb_input_core_join][974]
[dtv_app_mtk]>dfb_set_cursor_border [0,0,1280,0]
window size: 0
stacking [0x2], layer_id [0]
Init DSMCC[2][0][2]
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
EEPROM size is 0x70.
[dtv_app_mtk]>
[dtv_app_mtk]>
x_wifi_cli_init~~~
[dtv_app_mtk]>
[dtv_app_mtk]>
Rec_util_thread:buffer addr 0x00003d79b000,size 0x380000
EEPROM size is 0x70.
=====================
channel id:(1835137), svl rec id:(7), channel id in rec:(1835137), brdcst type:(2)
=====================
{CI}Is a CI+ CAM = 0, the mode = 0, cur mode = 0
{DT} Real Time Clock is available on this system.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]><AM> wakeup reason = 6
EEPROM size is 0x35b0.
EEPROM size is 0x4000.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[OT][_acfg_ch_lst_load_p1][723]: e_wakeup_reason = 6.
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
**********DirectFBInit()
[dtv_app_mtk]>
[dtv_app_mtk]> [RHXTV] c_rpc_reg_xtvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_chlist_op_hndlrs
[dtv_app_mtk]>SC_FCT_0: sched_getparam 509 error -1
[dtv_app_mtk]>SC_FCT_0: sched_getparam 511 error -1
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[MTCI0] MTCI_Init : 0
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[* GL DFB *] Create plane (ON layer) :1014d2d
[dtv_app_mtk]>[* GL DFB *] Create plane (ON window (Shared)) :1014d2b
[dtv_app_mtk]>{IOM} UART thread inited.
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>x_dbg_abort rm_op.c:4011 code:0x49000b
DRAM Channel A Calibration.
Byte 0 : Gating(2 ~ 77), Size=76, Mid=41, Set=41.
Byte 1 : Gating(2 ~ 62), Size=61, Mid=34, Set=34.
Byte 2 : Gating(2 ~ 87), Size=86, Mid=46, Set=46.
Byte 3 : Gating(2 ~ 82), Size=81, Mid=44, Set=44.
Byte 0 : DQS(5 ~ 43), Size 39, Set 23.
Byte 1 : DQS(8 ~ 40), Size 33, Set 22.
Byte 2 : DQS(6 ~ 41), Size 36, Set 21.
Byte 3 : DQS(11 ~ 38), Size 28, Set 20.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
0x0000a000
Nand boot
NID=0x9510dcec
LZHS addr:0x00100040
LZHS size:0x001f8fd0
LZHS checksum:0x00000042
Boot
Start Lmain
MT5880 Boot Loader v1.11
SIF_Master0: new design
Boot reason: A/C power on!!
[PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0)
-------------use external edid, disable internal edid------------------
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x d450f8, size: 24286)success!!
T8032 FW version: 18
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x73500 0x80
Detect NAND flash ID: 0x9510DCEC
Detect SS K9F4G08U0B/D NAND flash(SLC): 512MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000
NAND_BDM_Mount: Partid: 0, Total Block Count: 16, Bad Block Count: 0
1st MAC in EEP is valid (1c:5a:6b:41:25:e1)
1st : (1c:5a:6b:41:25:e1)
2nd : (1c:5a:6b:41:25:e1)
[PDWNC] Current state : 0x1
[PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6
PDWNC_PHILIPS_DetermineNextState : u4Current = 1
PDWNC_PHILIPS_DetermineNextState : system booting
PDWNC_PHILIPS_DetermineNextState : event = PDWNC_WAKE_UP_REASON_AC_POWER
Read EEPROM OK at PDWNC_PHILIPS_GetLoungeMode
PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0
Current = 0x1, Event = 0x6, Next = 0x1
[PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1
[PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_Init
USB0: Set GPIO63 = 1.
USB1: Set GPIO64 = 1.
Display 0x00efe5b8 background:0x00000000
Find panel index 215 from EEPROM
OSD_SetPlaneSwitchOrder[0,1,2],Switch[1,2,3]
---------- [SA7] vErrorHandleInit ----------
[SA7] Error handling init
[SA7] PANEL_GetPanelWidth=0x556, PANEL_GetPanelHeight=0x300 , wDrvGetOutputHTotal=0x898 , wDrvGetOutputVTotal=0x465
[SA7] PANEL_GetHTotalMax=0x6e6, PANEL_GetHTotalMin=0x5b0, PANEL_GetVTotalMax=0x3f0, PANEL_GetVTotalMin=0x314
[SA7] PANEL_GetPixelClkMax=80000000, PANEL_GetPixelClkMin=63000000
[SA7] PANEL_GetPixelClk60Hz = 0x45126c0
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=260, u2HSyncStart=1930, u2VSyncWidth=26, u2VSyncStart=1094
---------- [SA7] vErrorHandleSetByTiming end----------
---------- [SA7] vErrorHandleSetByPanel end----------
[SA7] vDDDSInit
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=30, u2HSyncStart=1382, u2VSyncWidth=3, u2VSyncStart=784
---------- [SA7] vErrorHandleSetByTiming end----------
vDrvSetOCLKClockSchemaInit.
[SA7] _fgVopllUseDDDS = True
[LVDS] VOPLL Initialize successful !
LDR_OsdDisplay(14, 0x00d65bc0, 1280, 291)
Color:14 BmpAddr:0x00d65bc0 Width:1280 Height:291
Panel 1366 x 768
*************u4BmpPitch=5120******************
Do USB upgrade
USB: Vbus turn up time = 1419 ms, Max =0 ms.
USB-0: insert.
USB-0: ClassCode= 0x9, u4Diff=120 ms.
FIND_CLASS_HUB.
HUB No USB Medium on Hub.
USB upgrade stop
Flash load lzhs header from 0x80000 to dram(0x1526170), size=2048
Decompression uboot to 0x00800000...
Flash load image from 0x80000 to dram(0x1526170), size=0x400ab
NAND_BDM_Mount: Partid=4, offset=0x300000, size=0x400000
NAND_BDM_Mount: Partid: 4, Total Block Count: 32, Bad Block Count: 0
Flash load tz from 0x21acfb(kernel) to dram(0x3f200000), size=0x2b1b6
secure boot ok
secure boot ok
Starting image...
▒
U-Boot 2011.12.12 (Sep 27 2013 - 10:33:26)
DRAM: 725.3 MiB
WARNING: Caches not enabled
NAND: Detect NAND flash ID: 0x9510DCEC
Detect SS K9F4G08U0B/D NAND flash: 512MB
512 MiB
0.0.0.0
In: serial
Out: serial
Err: serial
Boot from kernelA and rootfsA(partition 6)
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
Partition rootfsA defined at mtdparts:
ID:6, Offset:0x00000000, Size:0x00b00000
Loader succeeded in signature verification
## Booting kernel from Legacy Image at 00007fc0 ...
XIP Kernel Image ... OK
OK
Starting kernel ...
TZ Heap: start=0x3FA5C5C0, end=0x40000000
TZ dram: start=0x3F000000, end=0x40000000
[ 0.000000] timekeeping_init done
INIT: version 2.86 booting
Loading /etc/profile...
Start readahead /etc/readahead_early
Running rc.local...
net.ipv4.tcp_window_scaling = 6
INIT: Entering runlevel: 3
**********DirectFBInit()
commandline read: app_man
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
(c) 2001-2009 The world wide DirectFB Open Source Community
(c) 2000-2004 Convergence (integrated media) GmbH
----------------------------------------------------------------
======DFB 3DMM u4VirtAddr : 0x3a6c5000, and DFB 3DMM u4Size : 0x1f80000======
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
input thread's parent pid is 517 tid is 517
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[DirectFB]: Wait to Init IR...!
[input_add_device][1629]
dfb_set_cursor_border [0,0,1280,0]
[dtv_app_mtk]>drv_init as 0x39 model
[dtv_app_mtk]>drv_init as EU model
[dtv_app_mtk]>HDMI fast booting init...
[ 8.507639] NAND_SDM_Mount: Partid=15, offset=0x1d680000, size=0x2980000
input thread pid is 517 tid is 525
original scheduler policy 0
scheduler nice 0
original child scheduler policy 0 prio 0
new child scheduler policy 2 prio 99
Start to wait IR event...
[dtv_app_mtk]>
[dtv_app_mtk]>TVD MsgCtrl: NRL:60/40, PER:100/90
[dtv_app_mtk]>x_drv_init end!!
[dtv_app_mtk]>[ FakeDM ] Init...
[FakeDM] Init FM...
/dev is created./mnt is already existed. That is OK.
/mnt/usb is created.[FakeDM] FM inited...
[FakeDM] Init SMB...
[FakeDM] SMB inited...
[FakeDM] do coldboot start...
[DM] _dm_open_dev_thread: entered
[DM] _dm_nfy_req_thread enter
[DM] _dm_nfy_req_thread get_nl_sock:26
[DM] _dm_cb_msg_thread enter
[DM] usbfs mounted.
[FakeDM] do coldboot end!!!
Init chip_spec_init!!!!!
EEPROM size is 0x4000.
{CI_glue}:ci_eng_init
{CI_glue}- expect PROD key
{CI_glue}- c[1]
88888888888888 PHYSICAL_Init() entered 888888888888888
88888888888888 ITC_Init() entered 888888888888888
88888888888888 PHYS_DRVOpen() entered 888888888888888
88888888888888 STB_CIOpen() entered 888888888888888
88888888888888 STB_CIOpen() ended 888888888888888
{CI}CI_RegInterrupt_nfy
88888888888888 PHYS_DRVOpen() entered 888888888888888
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 255
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank Line 9708
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[dtv_app_mtk]>
[dtv_app_mtk]> ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
[dtv_app_mtk]> (c) 2001-2009 The world wide DirectFB Open Source Community
[dtv_app_mtk]> (c) 2000-2004 Convergence (integrated media) GmbH
[dtv_app_mtk]> ----------------------------------------------------------------
[dtv_app_mtk]>
[dtv_app_mtk]>[dfb_input_core_join][974]
[dtv_app_mtk]>dfb_set_cursor_border [0,0,1280,0]
window size: 0
stacking [0x2], layer_id [0]
Init DSMCC[2][0][2]
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
EEPROM size is 0x70.
[dtv_app_mtk]>
[dtv_app_mtk]>
x_wifi_cli_init~~~
[dtv_app_mtk]>
[dtv_app_mtk]>
Rec_util_thread:buffer addr 0x00003d79b000,size 0x380000
EEPROM size is 0x70.
=====================
channel id:(1835137), svl rec id:(7), channel id in rec:(1835137), brdcst type:(2)
=====================
{CI}Is a CI+ CAM = 0, the mode = 0, cur mode = 0
{DT} Real Time Clock is available on this system.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]><AM> wakeup reason = 6
EEPROM size is 0x35b0.
EEPROM size is 0x4000.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[OT][_acfg_ch_lst_load_p1][723]: e_wakeup_reason = 6.
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
**********DirectFBInit()
[dtv_app_mtk]>
[dtv_app_mtk]> [RHXTV] c_rpc_reg_xtvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_chlist_op_hndlrs
[dtv_app_mtk]>SC_FCT_0: sched_getparam 509 error -1
[dtv_app_mtk]>SC_FCT_0: sched_getparam 511 error -1
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[MTCI0] MTCI_Init : 0
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[* GL DFB *] Create plane (ON layer) :1014d2d
[dtv_app_mtk]>[* GL DFB *] Create plane (ON window (Shared)) :1014d2b
[dtv_app_mtk]>{IOM} UART thread inited.
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>x_dbg_abort rm_op.c:4011 code:0x49000b
Последнее редактирование модератором:
