Saturn LED40FHD500UST2 (CV358H-T42)/ Entering recovery system

Статус
В этой теме нельзя размещать новые ответы.

remtv

Участник
Регистрация
7 Май 2024
Сообщения
19
Возраст
57
Страна
Ukraine
Кредиты
132
Откуда
Одеса
Модель ТВ
Saturn LED40FHD500UST2
Main (шасси)
CV358H-T42
Panel (матрица)
V400HJ6-PE1
Main Board: CV358H-T42
panel: V400HJ6-PE1
Не выходил из дежурки и не читался терминальной прогой. Прошил программатором RT809H. Пробовал две прошивки от белорусов и сибирского форума, результат одинаковый, включается и весит на белом экране красная надпись SATURN. Становится видимым через терминал, читается лог и доступно приглашение MStar.
UART_115200

AC_ON
BIST0-OK
BIST1-OK
#_
AUTH_KEYBANK_FAIL
U
Relocation Offset is: 01600000
[AT][MB][start ub][556]

U-Boot 2011.06-00000-g375cd39-dirty (Mar 01 2019 - 09:02:40)

[Mboot] ===== sw IR Config Register =====
[Mboot] ===== Attach IR Interrupt ======
[SYS][Utopia]: Function = SYSOpen, Line = 1143, current resource pri_shm content is: 0
[SYS][Utopia]: Function = SYSOpen, Line = 1162, [SYS INFO] OPEN INSTANCE...
create instance at 2A6EB238 with private size 128 bytes at 2A6EB280
[ERROR] MstarSysInit:255: Optee OS is not running!!!
[MIU][Utopia]:
[MIU INFO] miu opencreate instance at 2A6EB308 with private size 80 bytes at 2A6EB350
create instance at 2A6EB3A8 with private size 48 bytes at 2A6EB3F0

uboot held at [2A4DDF60~2C000000],size=01B220A0
DRAM: 192 MiB
Now running in RAM - U-Boot at: 2B500000

eMMC: HS200 200MHz
eMMC 7.28 GB [E8FFF8h]
SAR5=ON
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Set MAC default
MAC: 0x0: 0x30: 0x1B: 0xBA:0x2: 0xDB
[CPU][Utopia]:
[CPU INFO] cpu opencreate instance at 2A6FB860 with private size 44 bytes at 2A6FB8A8
[CPU][Utopia]: CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[tu]: P+ P+аP+ P+`P+аP+xV4

[AT][MBoot][Driver Init][804]
Warning: U must forget reset bluetool module!!! Plz check it!

Changelist: 24543697
============= set bootargs ===============
Hit any key to stop autoboot: 0
setCtvFacTestMode==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
AC on
setCtvAtvDbEmpty==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
setClearFactoryDB==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
setCtvFacTestMode==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207500
[USB] UHC Base 1F204800
[USB] USBC Base 1F200E00
[USB] BC Base 1F246C00
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0xBEF8E00
[USB] Reg 0x28: 0x8E00 0xBEF
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value FF:
1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Check USB port[1]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 1 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207400
[USB] UHC Base 1F201A00
[USB] USBC Base 1F200F00
[USB] BC Base 1F246C40
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
Check USB port[2]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 2 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207200
[USB] UHC Base 1F227200
[USB] USBC Base 1F227000
[USB] BC Base 1F246C80
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
[ERROR] Factory_Check_Usb_Files:623: FAIL : can not init usb!!
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
fore uup u8KeyPad_KeyVal [0xFF]
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
AC on
env AutoFacMode = 0
env project_id =
setCtvFacTestMode==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
!!! [do_audiopreinit] Skip Power Music !!!
[ERROR] _get_new_map_format_from_env:540: get E_MMAP_ID_FRC_R2_ADR fail
[ERROR] do_frc_bringup:822: get E_MMAP_ID_FRC_R2 mmap fail
create instance at 2A6FBCA0 with private size 348 bytes at 2A6FBCE8
MDrv_PNL_Init u32PnlRiuBaseAddr = tx
MDrv_PNL_Init u32PMRiuBaseAddr = tx
[_MDrv_PNL_Init_LPLL][341]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_LPLL][343]u16HTotal=2200,u16VTotal=1130,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1130, u16DefaultVFreq=600
[_MDrv_PNL_Init_Output_Dclk][393]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_Output_Dclk][395]u16HTotal=2200,u16VTotal=1130,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1130, u16DefaultVFreq=600
[MApi_XC_MLG_GetStatus, 2698]No instance existed, please get an instance by calling MApi_XC_Init() first
[20181109][fl.du] 000 bUsingBurstWrite= 1
[20181109][fl.du] 000 bUsingBurstWrite= 1
[20181109][fl.du] 000 bUsingBurstWrite= 1

MsDrv_PNL_Init:Bypass SetDivison
[PWM][Utopia]: Init PWM0[AT][MB][panel_pre_init][4064]

[AT][MB][bootlogo begin][4066]
create instance at 2A6FBE48 with private size 312 bytes at 2A6FBE90
[AT][MB][JPD Decode][4109]

[UTOPIA INFO] close moduleNames[tu]: +`P+ P+аP+ P+`P+аP+xV4

[showLogo] GOP Boot Logo Index 2
create instance at 2A6FBE48 with private size 1728 bytes at 2A6FBE90
create instance at 2A6FC558 with private size 9596 bytes at 2A6FC5A0
[AT][MB][Show Logo][4156]
Unknown command 'readKL' - try 'help'

---MsDrv_PNL_BackLigth_On:1245 Set MsDrv_PNL_BackLigth_On DelayTask 102
!!! [do_bootmusic] Skip Power Music !!!
Unknown command 'bootKL' - try 'help'
## Booting Android Image at 0x24D00000 ...
Kernel load addr 0x20280000 size 13951 KiB
Kernel command line: dvariant=userdebug
RAM disk load addr 0x21280000 size 2732 KiB
ramdisk start = 0x25AA0800, ramdisk end = 0x25D4B52D
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Kernel Image ... OK
[AT][MB][start kr][4464]

Starting kernel ...

[ERROR] _get_new_map_format_from_env:540: get E_LX_MEM3_ADR fail
[ERROR] _get_new_map_format_from_env:540: get E_LX_MEM4_ADR fail
set 64 bit mode
armfw_real_va_addr : 5EBE3000
optee_real_va_addr : 5EE00000
ARM_FW_Enter_64 260 ARMv8 NS-Uboot for 64bit kernel
ARM_FW_Enter_64 261 25AA0800 2AAD2D 20200100
UART_115200

AC_ON
BIST0-OK
BIST1-OK
#_
AUTH_KEYBANK_FAIL
U
Relocation Offset is: 01600000
[AT][MB][start ub][556]

U-Boot 2011.06-00000-g375cd39-dirty (Mar 01 2019 - 09:02:40)

[Mboot] ===== sw IR Config Register =====
[Mboot] ===== Attach IR Interrupt ======
[SYS][Utopia]: Function = SYSOpen, Line = 1143, current resource pri_shm content is: 0
[SYS][Utopia]: Function = SYSOpen, Line = 1162, [SYS INFO] OPEN INSTANCE...
create instance at 2A6EB238 with private size 128 bytes at 2A6EB280
[ERROR] MstarSysInit:255: Optee OS is not running!!!
[MIU][Utopia]:
[MIU INFO] miu opencreate instance at 2A6EB308 with private size 80 bytes at 2A6EB350
create instance at 2A6EB3A8 with private size 48 bytes at 2A6EB3F0

uboot held at [2A4DDF60~2C000000],size=01B220A0
DRAM: 192 MiB
Now running in RAM - U-Boot at: 2B500000

eMMC: HS200 200MHz
eMMC 7.28 GB [E8FFF8h]
SAR5=ON
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Set MAC default
MAC: 0x0: 0x30: 0x1B: 0xBA:0x2: 0xDB
[CPU][Utopia]:
[CPU INFO] cpu opencreate instance at 2A6FB860 with private size 44 bytes at 2A6FB8A8
[CPU][Utopia]: CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[tu]: P+ P+аP+ P+`P+аP+xV4

[AT][MBoot][Driver Init][804]
Warning: U must forget reset bluetool module!!! Plz check it!

Changelist: 24543697
============= set bootargs ===============
Hit any key to stop autoboot: 0
setCtvFacTestMode==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
AC on
setCtvAtvDbEmpty==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
setClearFactoryDB==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
setCtvFacTestMode==bootargs =console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init CORE_DUMP_PATH=/data/core_dump.%%p.gz KDebug=1 delaylogo=true androidboot.selinux=permissive security=selinux platform=sn SD_CONFIG=3 str_ignore_wakelock loglevel=0 EMAC_MEM=0x100000 PM51_ADDR=0x20010000 PM51_LEN=0x10000 SAR5=ON MIRROR=0 BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x0 ENV_VAR_SIZE=0x10000 ENV=EMMC SECURITY=OFF IsUseFactorCmdbBin=0 atvdb_empty=1 ctv_cleardb=0 factory_mode=1 upgrade_stat=0 LX_MEM=0x1AB00000 LX_MEM2=0xA0400000,0x1FC00000 tee_mode=optee recovery_fbaddr=0x1B800000 pm_path=/tvconfig/config/PM.bin CMA0=OTHERS,miu=0,hid=23,sz=0x4400000,st=0x6c00000 CMA1=VDEC_XC_STR_MBOOT,miu=0,hid=20,sz=0x3000000,st=0xb000000 CMA2=RETURN_ENUM0,miu=0,hid=26,sz=0x800000,st=0xe000000 CMA3=RETURN_ENUM2,miu=1,hid=27,sz=0x1400000,st=0x400000 CMA4=VDEC1,miu=1,hid=19,sz=0x7c00000,st=0x1800000
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207500
[USB] UHC Base 1F204800
[USB] USBC Base 1F200E00
[USB] BC Base 1F246C00
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0xBEF8E00
[USB] Reg 0x28: 0x8E00 0xBEF
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value FF:
1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Check USB port[1]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 1 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207400
[USB] UHC Base 1F201A00
[USB] USBC Base 1F200F00
[USB] BC Base 1F246C40
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
Check USB port[2]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2014.10.02
[USB] Port 2 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1F207200
[USB] UHC Base 1F227200
[USB] USBC Base 1F227000
[USB] BC Base 1F246C80
[USB] config miu select [30] [74] [FF] ][FF]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
[ERROR] Factory_Check_Usb_Files:623: FAIL : can not init usb!!
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
Boot Check: Reboot by WDT --------
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
fore uup u8KeyPad_KeyVal [0xFF]
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
AC on
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
!!! [do_audiopreinit] Skip Power Music !!!
[ERROR] _get_new_map_format_from_env:540: get E_MMAP_ID_FRC_R2_ADR fail
[ERROR] do_frc_bringup:822: get E_MMAP_ID_FRC_R2 mmap fail
create instance at 2A6FBCA0 with private size 348 bytes at 2A6FBCE8
MDrv_PNL_Init u32PnlRiuBaseAddr = tx
MDrv_PNL_Init u32PMRiuBaseAddr = tx
[_MDrv_PNL_Init_LPLL][341]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_LPLL][343]u16HTotal=2200,u16VTotal=1130,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1130, u16DefaultVFreq=600
[_MDrv_PNL_Init_Output_Dclk][393]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_Output_Dclk][395]u16HTotal=2200,u16VTotal=1130,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1130, u16DefaultVFreq=600
[MApi_XC_MLG_GetStatus, 2698]No instance existed, please get an instance by calling MApi_XC_Init() first
[20181109][fl.du] 000 bUsingBurstWrite= 1
[20181109][fl.du] 000 bUsingBurstWrite= 1
[20181109][fl.du] 000 bUsingBurstWrite= 1

MsDrv_PNL_Init:Bypass SetDivison
[PWM][Utopia]: Init PWM0[AT][MB][panel_pre_init][3987]

[AT][MB][bootlogo begin][3989]
create instance at 2A6FBE48 with private size 312 bytes at 2A6FBE90
[AT][MB][JPD Decode][4032]

[UTOPIA INFO] close moduleNames[tu]: +`P+ P+аP+ P+`P+аP+xV4

[showLogo] GOP Boot Logo Index 2
create instance at 2A6FBE48 with private size 1728 bytes at 2A6FBE90
create instance at 2A6FC558 with private size 9596 bytes at 2A6FC5A0
[AT][MB][Show Logo][4079]
Unknown command 'readKL' - try 'help'

---MsDrv_PNL_BackLigth_On:1245 Set MsDrv_PNL_BackLigth_On DelayTask 102
!!! [do_bootmusic] Skip Power Music !!!
Unknown command 'bootKL' - try 'help'
## Booting Android Image at 0x24D00000 ...
Kernel load addr 0x20280000 size 13951 KiB
Kernel command line: dvariant=userdebug
RAM disk load addr 0x21280000 size 2732 KiB
ramdisk start = 0x25AA0800, ramdisk end = 0x25D4B52D
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Kernel Image ... OK
[AT][MB][start kr][4387]

Starting kernel ...

[ERROR] _get_new_map_format_from_env:540: get E_LX_MEM3_ADR fail
[ERROR] _get_new_map_format_from_env:540: get E_LX_MEM4_ADR fail
set 64 bit mode
armfw_real_va_addr : 5EBE3000
optee_real_va_addr : 5EE00000
ARM_FW_Enter_64 260 ARMv8 NS-Uboot for 64bit kernel
ARM_FW_Enter_64 261 25AA0800 2AAD2D 20200100
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >>#
<< MStar >># help
? - alias for 'help'
CmdPerformanceTest- gettime - Get the system executing time

ac - set a new config to the bootargs

audio_preinit- audio_preinit - Init audio driver

auto_flash- do auto flash image.

auto_tftp- do auto-address tftp.

base - print or set address offset
bdinfo - print Board Info structure
bin2emmc- bin2emmc - read bin file and restore it to emmc

boot - boot default, i.e., run 'bootcmd'
bootargs_set- Set info exchange and set to boot args.
bootcheck- bootcheck - Do boot check

bootd - boot default, i.e., run 'bootcmd'
bootlogo- bootlogo - Display Logo_Music

bootm - boot application image from memory
bootmusic- bootmusic - play music

bootp - boot image via network using BOOTP/TFTP protocol
checkVersion- check current verison and upgrade image version

checkfile- check file exist in u disk,and set the partition.
checkstr- check_str_resume

checktee- Check TEE binary
cleanallenv- cleanall environment variables to persistent storage
cmp - memory compare
config2env- Set config to environment.
config_raw_io- Config the target device for raw I/O
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
custar - do usb update from the specified file that is in usb.

dbg - set debug message level. Default level is INFO
dbtable_init- dbtable_init - let data is ready (logo, music, panel, ursa).

dc - delete the specific cofig that is in the bootargs

delay - delay time, time unit is ms

destroy_logo- destroy_logo - Stop logo display

dhcp - boot image via network using DHCP/TFTP protocol
draw_jpg- blt_jpg - Blt JPG

draw_pixel- draw_pixel - draw a pixel with color

draw_progress- draw_string - draw string with color

draw_rect- draw_rect - draw rect with color

draw_string- draw_string - draw string with color

du - du - Disable UART

ebist - PHY loopback test
echo - echo args to console
editenv - edit environment variable
edump - EMAC Register settings dump
eloopback- Long loopback test
emmc - eMMC sub system
emmcbin - emmcbin - dump emmc and restore it to fat usb disk

emmcbootbin- emmcbootbin - dump emmc boot partition and write it to fat usb disk

env - environment handling commands
envload - envload - reload the nand environment.

epd - emac power down
estart - EMAC start
ewavetest- EMAC wave test
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
ext4filesize- get file size from a Ext4 filesystem
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4partload- part load binary file from a Ext4 filesystem
factory_check_usb_files- factory mode to check usb files and do test

false - do nothing, unsuccessfully
fastboot- enter fastboot mode
fatfilesize- fatfilesize - load binary file from a dos filesystem

fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatpartload- fatpartload - load binary file from a dos filesystem

fatwrite- fatwrite - write binary file to a dos filesystem

filelist- Dump the file list.

filelisttest- This command is only for file list test

filepartload- load part of a file to RAM
filepartloadSeg- load a seg part of file to RAM
flashbin- flashbin - dump/restore emmc or nand flash data to/from flash.bin

frcrcv - frcrcv - do_frc_recv

frcsnd - frcsnd - do_frc_send

frcup - frcup - do_frc_bringup

get_mmap- get memory info from supernova's mmap
gettime - gettime - Get the system executing time

go - start application at address 'addr'
gpio - GPIO Command:
help - print command description/usage
i2c - I2C sub-system
if_boot_to_pm- if boot to PM

iminfo - print header information for application image
imxtract- extract a part of a multi-image
initDbgLevel- Initial varaible 'dbgLevel'
init_raw_io- init raw_io module
itest - return true/false on integer compare
kbup - kbup - update key bank

kernelProtect- kernelProtect - Protect kernel

kernelProtectBist- kernelProtectBist - Protect kernel bist

led - See led commands
loadb - load binary file over serial line (kermit mode)
loadenv - loadenv - load env for nand

loads - load S-Record file over serial line
loadspi - load data from SPI
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
m2e - Restore the address and len to env from supernova's mmap

macaddr - setup EMAC MAC addr
mbootver_set- setmbootver - for customer show in factory menu.

mbup - mboot upgrade

md - memory display
memtest - Get the performance of memory
miuProtect- miuProtect - Protect miu

mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcbininfo- mmcbininfo - Valid block num in each partition

mmcinfo - display MMC info
mmcreg - mmcreg show ext-csd
mscompress7- Compress or decompress lzma files
msg - print string - msg [string]

mstar - update kernal & root file system automatically by script file
mtest - simple RAM read/write test
mversion- show changelist - mversion

mw - memory write (fill)
nm - memory modify (constant address)
nuttxProtect- nuttx Protect - Protect nuttx

osd_create- osd_create - create osd layer

osd_destroy- osd_destroy - destroy osd layer

osd_flush- osd_flush - flush canvas to screen

ota_zip_check- do OTA zip package check.

panel_init- panel_init - init panel by panel.ini

panel_post_init- backligth on - backlight on

panel_pre_init- panel_pre_init - init panel by panel.ini

pcietest- PCIE test system
ping - send ICMP ECHO_REQUEST to network host
pm51 - pm51 command: pm51 [option]

pmProtect- runtime pm Protect - Protect runtime PM

pop_raw_io_config- pop raw_io last config
printenv- print environment variables
push_raw_io_config- push raw_io current config
raw_io_status- get raw_io status
raw_read- Read the raw datas that store in the target device
Yo have to execute 'config_raw_io' before using this cmd

raw_write- Write the raw datas that store in the target deviceYo have to execute 'config_raw_io' before using this cmd

readArmFw- readArmFw - read Nuttx to malloc buffer

readOptee- readOptee - core1 run at Nuttx

recovery_wipe_partition- do recovery wipe data or cache.

reset - Perform RESET of the CPU
riu - riu - riu command

run - run commands in an environment variable
sar - sar Command:
saveenv - save environment variables to persistent storage
setenv - set environment variables
showtb - Show register command table. - showtb [stage]

showvar - print local hushshell variables
showversion- Show version
sleep - delay execution for some time
smc - smc - jump to arm_trusted_firmware

source - run script from memory
sparse_write- do sparse image writing to target flash type.

spi2usb - Read data from spi to usb
sync_mmap- Sync the some id's address and len to env and bootargs from supernova's mmap

test - minimal test like /bin/sh
testmode- set testmode into bootargs.
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
udstar - Execute the script file that is stored in usb disk

unlockcmi- unlock cmi transfer board - unlock

update_mode- get/set update_mode

updatemiureg- Call driver to update miu setting
usb - USB sub-system
usb2spi - write data from usb to spi
usb_bin_check- do usb bin document check.

usb_partial_upgrade_to_emmc- partial upgrade from USB to eMMC

usbboot - boot from USB device
ustar - ustar - update kernal & root file system automatically by script file

version - print monitor, compiler and linker version
wdt_enable- wdt_enable n - set Watchdog timer to n secs

<< MStar >># help
? - alias for 'help'
CmdPerformanceTest- gettime - Get the system executing time

ac - set a new config to the bootargs

audio_preinit- audio_preinit - Init audio driver

auto_flash- do auto flash image.

auto_tftp- do auto-address tftp.

base - print or set address offset
bdinfo - print Board Info structure
bin2emmc- bin2emmc - read bin file and restore it to emmc

boot - boot default, i.e., run 'bootcmd'
bootargs_set- Set info exchange and set to boot args.
bootcheck- bootcheck - Do boot check

bootd - boot default, i.e., run 'bootcmd'
bootlogo- bootlogo - Display Logo_Music

bootm - boot application image from memory
bootmusic- bootmusic - play music

bootp - boot image via network using BOOTP/TFTP protocol
checkVersion- check current verison and upgrade image version

checkfile- check file exist in u disk,and set the partition.
checkstr- check_str_resume

checktee- Check TEE binary
cleanallenv- cleanall environment variables to persistent storage
cmp - memory compare
config2env- Set config to environment.
config_raw_io- Config the target device for raw I/O
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
custar - do usb update from the specified file that is in usb.

dbg - set debug message level. Default level is INFO
dbtable_init- dbtable_init - let data is ready (logo, music, panel, ursa).

dc - delete the specific cofig that is in the bootargs

delay - delay time, time unit is ms

destroy_logo- destroy_logo - Stop logo display

dhcp - boot image via network using DHCP/TFTP protocol
draw_jpg- blt_jpg - Blt JPG

draw_pixel- draw_pixel - draw a pixel with color

draw_progress- draw_string - draw string with color

draw_rect- draw_rect - draw rect with color

draw_string- draw_string - draw string with color

du - du - Disable UART

ebist - PHY loopback test
echo - echo args to console
editenv - edit environment variable
edump - EMAC Register settings dump
eloopback- Long loopback test
emmc - eMMC sub system
emmcbin - emmcbin - dump emmc and restore it to fat usb disk

emmcbootbin- emmcbootbin - dump emmc boot partition and write it to fat usb disk

env - environment handling commands
envload - envload - reload the nand environment.

epd - emac power down
estart - EMAC start
ewavetest- EMAC wave test
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
ext4filesize- get file size from a Ext4 filesystem
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4partload- part load binary file from a Ext4 filesystem
factory_check_usb_files- factory mode to check usb files and do test

false - do nothing, unsuccessfully
fastboot- enter fastboot mode
fatfilesize- fatfilesize - load binary file from a dos filesystem

fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatpartload- fatpartload - load binary file from a dos filesystem

fatwrite- fatwrite - write binary file to a dos filesystem

filelist- Dump the file list.

filelisttest- This command is only for file list test

filepartload- load part of a file to RAM
filepartloadSeg- load a seg part of file to RAM
flashbin- flashbin - dump/restore emmc or nand flash data to/from flash.bin

frcrcv - frcrcv - do_frc_recv

frcsnd - frcsnd - do_frc_send

frcup - frcup - do_frc_bringup

get_mmap- get memory info from supernova's mmap
gettime - gettime - Get the system executing time

go - start application at address 'addr'
gpio - GPIO Command:
help - print command description/usage
i2c - I2C sub-system
if_boot_to_pm- if boot to PM

iminfo - print header information for application image
imxtract- extract a part of a multi-image
initDbgLevel- Initial varaible 'dbgLevel'
init_raw_io- init raw_io module
itest - return true/false on integer compare
kbup - kbup - update key bank

kernelProtect- kernelProtect - Protect kernel

kernelProtectBist- kernelProtectBist - Protect kernel bist

led - See led commands
loadb - load binary file over serial line (kermit mode)
loadenv - loadenv - load env for nand

loads - load S-Record file over serial line
loadspi - load data from SPI
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
m2e - Restore the address and len to env from supernova's mmap

macaddr - setup EMAC MAC addr
mbootver_set- setmbootver - for customer show in factory menu.

mbup - mboot upgrade

md - memory display
memtest - Get the performance of memory
miuProtect- miuProtect - Protect miu

mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcbininfo- mmcbininfo - Valid block num in each partition

mmcinfo - display MMC info
mmcreg - mmcreg show ext-csd
mscompress7- Compress or decompress lzma files
msg - print string - msg [string]

mstar - update kernal & root file system automatically by script file
mtest - simple RAM read/write test
mversion- show changelist - mversion

mw - memory write (fill)
nm - memory modify (constant address)
nuttxProtect- nuttx Protect - Protect nuttx

osd_create- osd_create - create osd layer

osd_destroy- osd_destroy - destroy osd layer

osd_flush- osd_flush - flush canvas to screen

ota_zip_check- do OTA zip package check.

panel_init- panel_init - init panel by panel.ini

panel_post_init- backligth on - backlight on

panel_pre_init- panel_pre_init - init panel by panel.ini

pcietest- PCIE test system
ping - send ICMP ECHO_REQUEST to network host
pm51 - pm51 command: pm51 [option]

pmProtect- runtime pm Protect - Protect runtime PM

pop_raw_io_config- pop raw_io last config
printenv- print environment variables
push_raw_io_config- push raw_io current config
raw_io_status- get raw_io status
raw_read- Read the raw datas that store in the target device
Yo have to execute 'config_raw_io' before using this cmd

raw_write- Write the raw datas that store in the target deviceYo have to execute 'config_raw_io' before using this cmd

readArmFw- readArmFw - read Nuttx to malloc buffer

readOptee- readOptee - core1 run at Nuttx

recovery_wipe_partition- do recovery wipe data or cache.

reset - Perform RESET of the CPU
riu - riu - riu command

run - run commands in an environment variable
sar - sar Command:
saveenv - save environment variables to persistent storage
setenv - set environment variables
showtb - Show register command table. - showtb [stage]

showvar - print local hushshell variables
showversion- Show version
sleep - delay execution for some time
smc - smc - jump to arm_trusted_firmware

source - run script from memory
sparse_write- do sparse image writing to target flash type.

spi2usb - Read data from spi to usb
sync_mmap- Sync the some id's address and len to env and bootargs from supernova's mmap

test - minimal test like /bin/sh
testmode- set testmode into bootargs.
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
udstar - Execute the script file that is stored in usb disk

unlockcmi- unlock cmi transfer board - unlock

update_mode- get/set update_mode

updatemiureg- Call driver to update miu setting
usb - USB sub-system
usb2spi - write data from usb to spi
usb_bin_check- do usb bin document check.

usb_partial_upgrade_to_emmc- partial upgrade from USB to eMMC

usbboot - boot from USB device
ustar - ustar - update kernal & root file system automatically by script file

version - print monitor, compiler and linker version
wdt_enable- wdt_enable n - set Watchdog timer to n secs

<< MStar >>#
задал две команды чере терминал:
- recovery_wipe_partition-
- reset
На экране получил ракету с надписью "Entering recovery system"

Ищу USB прошивку или помощь в прошивке через програматор, структура файлов считаного и скаченого разная

main.jpg
shild.jpg
panel.jpg
raketa.jpg
001.jpg00211.png
 
Статус
В этой теме нельзя размещать новые ответы.

Сверху